濟南電纜橋架的腐蝕原因有哪些?
濟南電纜橋架現在的適用范圍比較廣泛和靈活，它不僅可以單獨進行架設，也可以平鋪在各種建筑物的支架上。但是常常會有一些老化和腐蝕的情況，大家想必也遇到過，今天我們就來找一找相關的原因，幫助大家進一步了解。
Jinan cable bridge is widely used and flexible. It can not only be erected alone, but also be laid on the supports of various buildings. But there are often some aging and corrosion conditions, you must have encountered, today we will find out the relevant reasons, to help you understand.
1.絕緣的受潮情況：這種情況經常發生，經常發生在直埋或排氣管內的電纜接頭處;
1. Insulation dampness: this kind of situation often occurs at the cable joint directly buried or in the exhaust pipe;
2.化學原料腐蝕：如果電纜直接埋在酸堿區，往往會構成電纜腐蝕。鉛皮或外保護層被腐蝕，維修層長期遭受化學腐蝕或電解腐蝕，導致維修層失效，絕緣下降，也會導致電纜問題;
2. Chemical raw material corrosion: if the cable is directly buried in the acid-base area, it will often constitute cable corrosion. The lead skin or outer protective layer is corroded, and the maintenance layer suffers from chemical corrosion or electrolytic corrosion for a long time, which leads to the failure of the maintenance layer and the degradation of insulation, which also leads to cable problems;
3.長期過載運行：進行過載運行和長期過載運行時，溫度過高會加速絕緣老化，導致絕緣擊穿。
3. Long term overload operation: during overload operation and long-term overload operation, too high temperature will accelerate insulation aging and cause insulation breakdown.
4.電纜接頭故障：電纜接頭是整個線路的脆弱部分，經常發生由人員直接故障(施工不良)引起的電纜接頭故障。濟南電纜橋框架表明，如果在電纜接頭制造過程中接頭沒有緊密卷曲。原有網絡加熱不充分會造成電纜頭絕緣下降，進而引發故障。
4. Cable joint failure: the cable joint is a vulnerable part of the whole line, which is often caused by the direct fault of personnel (poor construction). Jinan cable bridge frame shows that if the joint is not tightly crimped during the manufacturing process of cable joint. The insufficient heating of the original network will cause the cable head insulation to drop, and then cause the fault.
5.環境中的溫度因素：電纜橋框架及其部件周圍的外部環境和熱源也會導致電纜溫度過高，絕緣擊穿，嚴重爆炸引起火災。
5. Temperature factors in the environment: the external environment and heat source around the cable bridge frame and its components will also lead to high temperature of the cable, insulation breakdown, serious explosion and fire.
濟南電纜橋架如果出現老化腐蝕現象時，比較簡單的方法是鍍鋅處理一下，通過這種方法可以在表面生成一層鉛材料膜，有利于減緩它的腐蝕和腐蝕速度。
If there is aging corrosion phenomenon in Jinan cable bridge, the simple method is galvanizing. Through this method, a layer of lead material film can be formed on the surface, which is conducive to slow down its corrosion and corrosion rate.
